Category Archives: Oscilloscopes

G Scan2 Oscilloscope functions

measure1

G Scan2 Oscilloscope functions
Measure Menu

Measures the voltage or amperage fluctuations of the vehicle’s sensor or actuator circuits in rapid succession and visualises the signals in the graphic waveforms.
Measure Mode

 

measure2Measurement of a vehicles engine cylinder compression is also possible by the use of optional pressure sensor.

 
4ch014 Channel Mode With Aux. Input

 

 

 
2ch012 Channel Mode With Aux. Input

 

 

 

 

24ch012/4 Channel Mode Single Pattern

 

 

 
trigger01Trigger Setting By Screen Touch

 

 

 

 

vmDigital Multi-Meter
volt meter

G-scan 2 provides digital meter function through the VMI that performs the measurement of voltage, resistance, frequency, duty cycle and pulse width as well as the continuity test.
resistance
rmResistance Meter

 

 

 
ctContinuity Test

 

 

 
fmFrequency Meter

 

 

 
pmPulse Width Meter

 

 

 

 

Simulation Function

G-scan 2 can actively send out the electric signals to the vehicle’s sensor or actuator circuit for in-depth diagnostic purposes.
svsoSimulation-Voltage Signal Output

 

 
sdsoSimulation-Duty Signal Output

 

 

 
sfsoSimulation-Frequency Signal Output

 

 

 

 

In addition to finding the cause of the problem with the 2/4 channel oscilloscope, G-Scan 2 gives you the ability to measure current amps and secondary ignition using these optional probes.
simulation frequency
GS2scope_probeCOP Quick Pick-up Probe
Used for picking up the secondary ignition voltage by placing the tip on top of the ignition coil for the COP (Coil On Plug) / DIS (Direct Ignition System) where the ignition coil is placed on top of every cylinder.

 

 

 
IgnitionProbeHT_1Ignition HT Probe (High-Voltage Cable)
Used for picking up the secondary igition voltage by clamping the high tension (voltage cord of the distributor or the 2 ignition cables of the DLI (Distributor-less Ignition) ignition coil.

 

 

 

 

GS2Leads_optionGS2 Leads Optional
Blue – 2x24mm(F)
BNC(F) Adaptors
Red-BNC (M) Adaptor
The optional 4mm ‘Banana Jack’ and ‘BNC’ adaptors allow you to use your own existing leads or High and Low amp clamps, Coil on plug probe, or Distributor-less ignition HT system probes through the CH. AUX setting when registered to the G-Scan.

 

 

 

 

 

 

 

 

 

GS2_CurrentClampCurrent Clamps
60A & 600A Current Clamps
Measures high and low current amperes with the inductive amps clamp.

TEXA Opabox

prod-gasbox-opabox-autopower(2)OPABOX Autopower

OPABOX Autopower is a partial flow opacity meter for diesel engines. It incorporates a latest generation exhaust gas analysis chamber developed to conform to international standards.

Thanks to Power Pack and Bluetooth technology, TEXA exhaust gas analysis solutions eliminate all those awkward cables trailing around the workshop, between the analysers and the display units, and between the analysers and the mains power supply too.

prod-gasbox-autopower(5)OPABOX Autopower is designed to be practical and versatile, and meets the full range of requirements of mechanics in the field of exhaust gas analysis.
The analysis chamber is incorporated in a practical trolley mounted on wheels with ball bearings. The analyser can therefore be moved effortlessly to the vehicle waiting to be tested.

prod-g-gasbox-opabox-02(1)_1GASBOX Autopower is an exhaust gas analyser for petrol, LPG, and methane fuelled engines. It incorporates TEXA’s own analysis chamber and comes with a practical trolley for easy movement around the workshop.

prod-g-gasbox-opabox-03(1)_1To make it even more flexible, as well as being plugged into any standard mains power socket, GASBOX can also be used with Power Pack, a practical battery module that can be removed and recharged separately. This clever solution means that you can always have one or more batteries charged and ready for use.

GASBOX Autopower

DIMENSIONS
460 x 200 x 250 mm

WEIGHT
  6,5 Kg (with trolley 15 kg)EXTERNAL POWER SUPPLY  2 x 12 V 7 A/h lead batteries; Maximum consumption: 80 W

SERIAL PORT  RS232 standard

WIRELESS OUTPUT  Bluetooth

SOFTWARE  ETS or IDC4

RESET AND CALIBRATION  electronic and automatic

TECHNOLOGY  NDIR

CONDENSATE DRAINAGE  continuous and automatic

RESPONSE TIME  < 10 seconds

HEATING TIME  Max. 60 seconds

OPABOX Autopower

DIMENSIONS
  460 x 200 x 250 mmWEIGHT  6,5 Kg (with trolley 15 kg)

EXTERNAL POWER SUPPLY 2 x 12 V 7 A/h lead batteries; Maximum consumption: 80 W

SERIAL PORT  RS232 standard

WIRELESS OUTPUT  Bluetooth

SOFTWARE  ETS o IDC4

RESET AND CALIBRATION  electronic and automatic

TECHNOLOGY  Green Led diode

HEATING TIME  maximum 5 minutes

CHAMBER LENGTH  200 mm

TEMPERATURE  75°C

Texa Uniprobe

banner-uniprobe-eng(1)
The UNIProbe is an device for analogue and digital type measurements; the best and most complete solution for all traditional diagnosis tests. The UNIProbe allows for the complete multi-make diagnosis and can intervene on cars, motorcycles, scooters, quad bikes and boats, as well as on light and heavy commercial vehicles, coaches and agricultural vehicles.

prod-g-uniprobe-03The UNIProbe communicates with all TEXA display units or with a Windows PC with USB connection or through Bluetooth technology, allowing the technician absolute freedom of movement around the vehicle and in the workshop. It’s also fitted with an interior lithium battery that can guarantee exceptional autonomy. The UNIProbe reflects the TEXA philosophy on “two unit solutions” to the full, looking to completely eliminate wires within the workshop.

prod-uniprobe-oscilloscopio-01-engUNIProbe incorporates 6 different instruments in the one unit, including an oscilloscope with four independent channels that can take accurate and professional measurements from voltage sensors and current clamps.

UNIProbe lets you test batteries, starting and charging systems, perform electrical tests on CAN networks, measure voltage and resistance using a built-in multimeter, and measure fuel pressure with an external electronic sensor.

You can even use a signal generator to simulate the PWM signals produced by sensors and the PWM power signals that drive electromechanical actuators like solenoid valves and common rail pressure regulators.
Texa_range_4

Texa Twin Probe

banner-twinprobe-engTwinProbe is the TEXA tool for acquiring the analogue and digital measurements needed for all conventional diagnostic testing. It comes at a lower price than UNIProbe, its “big brother”, however both share in common outstanding practicality and precision for all automotive service operations. TwinProbe communicates with all TEXA viewing units or with a Windows PC with USB connection or through Bluetooth Technology, allowing the mechanic absolute freedom of movement around the vehicle and in the workshop. The tool can be managed by the IDC4 operating software, or MSS (Measurement System Software) when used on a PC.

OSCILLOSCOPE

TwinProbe is an oscilloscope with two independent analogue channels for inputs up to ± 200V, complete with SIV (Signal information Viewing ) function for interpreting the measured signal. The SIV function guides you through the entire test procedure. TwinProbe not only displays the signal but, while taking measurements and acquiring data, simultaneously processes and analyses information in order to provide real time evaluations. TwinProbe can process signals from various sensors and actuators and compare the data acquired against values stored in the internal database, immediately highlighting any signal anomalies.

SIGNAL GENERATOR

The practical TwinProbe signal generator is ideal for simulating input signals from sensors and the signals transmitted by ECUs to control actuators like solenoid valves, in order to detect and analyse faults in the system.

AMMETER

TwinProbe can also be used to measure current intensity. An optional BICOR clamp-on ammeter is needed to allow TwinProbe to run these tests.

prod-uniprobe-oscilloscopio-01-engMEASUREMENT SYSTEM SOFTWARE

Easy access to the amazing functions of TwinProbe is ensured by MSS (Measurement System Software), developed by TEXA especially for this device, and by the complete IDC4 software Platform.

The SIV (Signal Information Viewing) function deserves a special mention. This uses a software algorithm developed by TEXA specifically to compare acquired data with values recorded in an internal database. Unusual signals can therefore be identified instantly, making your work faster and easier than ever.

Petroject Videos

2010-11-17 19.48.29Petroject deliver training across the country, ranging from small sessions to larger multi day seminars. The problem with Training in New Zealand is it can be long winded, irrelevant, or just too difficult to access.
We love to get out on the road and bring World Class training to your area.

Course modules available for workshops include:
• EFi Component testing
• Oscilloscopes
• Scan tool Essentials
• Advanced Scanning
• Better Business development
• CAN networks (of course!)
• Fly-by-wire
• Ignition taming
• Gas Analysis and many more

We also have a range of videos to assist you too:-

Hanatech Scan tool demonstration  |  Bosch KTS Software instal
Hanatech Software updates  |  Bosch Scan Tool Demo
Diagnostics of Distinction Conference

 

 

Hanatech Feedback form

Hanatech LogoL
Feedback from qualified technicians about the Hanatech machine and software is invaluable, and helps us develop the service tool further. Please take time to complete the form below, listing as many details  as possible. Wherever possible, if we are aware of a fix or solution we can advise you, but a response will come from Hanatech and we will do our utmost to advise you of the results, and wherever possible it will result in a further update.

We thank you for your co-operation.

 

Hanatech Multi/Ultrascan support

Hana_ECAE_15

Mike & Adam Ross of East City Auto Electrical. First owner of a Hanatech in NZ. 15 years ago, and Mike says he still uses his trusty ol’ DCN-Pro!

A current subscription will enable you to use your Hanatech service tool to the best of it’s abilities. We strongly recommend that the machine gets plugged in via USB and updates are run regularly. This will enable the machine to run at it’s optimised best. We strongly advise you to set a reminder on your PC about running updates, and plugging it in at night leaves it ready to go in the morning!

The Hanatech technicians regularly update software and patches for updates on a range of vehicles including cars from Japan, which is ideal for the range of imports that we see on our shores. Also, having a machine in current subscription allows the technician to select from previous options of software (Rolling) to best serve the vehicle you have in your workshop.

TRIAL

After running the latest updates, the machine will time out from HostPro. We strongly urge you to re-connect and repeat the procedure, BUT instead of “Latest Version” select “TRIAL” version from the drop down box at the top, and run this option. It will NOT over ride latest versions, but will give you TRIAL versions which is where Hanatech development work is being undertaken, and you can use these options for scanning vehicles as well. Which will give you a greater range on your service tool. (And don’t forget to keep these updated too!)

Rolling? Forward and back

hostpro

So much data and functions is crammed into these 512mb cards, so inevitably it can get a bit crammed, and NO Communication Errors occur, nothing can be worse than plugging into a regular visitor, and NOT being able to scan, so this necessitates the need to roll the software. To do this, connect scan tool to Host-Pro but instead of selecting “Scan Latest Version” change this to Scan Previous or Scan OLD versions. But do NOT select ALL manufacturers, just the make of vehicle that you are working on, and Update the software to either of these, and this will increase the range of vehicles and options available to you. BUT for good working practices, ROLL the software back to latest versions after you have finished.

Click here to download HostPro software 1.78.